Model: WL10
Introduction
The MerryIoT Leak Detector is a quality product provided by Browan Inc. under their Smart Home brand MerryIoT. It is designed to be used for detection of water leaks.
It is a compatible device within the Lithium App, and it is used under the Water category.
Quick Setup (Lithium App)
Step 1. Remove the packaging and activate the device, by long pressing the Test Button on the side of the sensor for 5 seconds. Once the sensor joins the network, the LED will keep on for 3 seconds.
Step 2. Enrol the sensor in your account, by opening the Lithium App, touching the + (plus) icon under “Your Devices.” drawer list, and easy scanning the QR code on the side of the sensor.
Step 3. If your device is a compatible model and it is enrolled in the Lithium system, the “Add Sensor” screen will be displayed, for you to check the details and use the map to fine tune the location of the sensor, by touching in the green circular area.
Info: The location is your current mobile device GPS location, and you can move the sensor pin freely around your location (no more than 500m away). If you need to place the sensor at a remote location, this is NOT possible. You need to be physically present in the installation location (+/- 500m to consider the GPS inaccuracies).
Step 4. Place the device in a potentially flooded area, such as under a water radiator, under a sink pipes, under connection valves, etc.
Test
Now the sensor is installed. You DO NOT have to create a real Water emergency on the public map to test if the sensor is properly sending signals.
Press the Test Button on the side of the sensor. The Blue LED will blink quickly and you should receive a Test Push Notification from the Lithium App.
Now everything works properly. You are DONE!
How does the sensor work within Lithium App?
Keep-Alive
While Idle, the sensor will transmit a Keep-Alive control signal, every hour (60 min), containing the state of the sensor (dry or wet).
Error State
If the sensor is not sending any data, not even the Keep-Alive signal at all within 24 hours, it will move into Error State and you will receive a notification to make you aware and allow you to check for any issue.
Trigger
The sensor will send data upon dry/wet status change. If the sensor sends the Wet status, then a Water emergency is triggered and published on the map, alerting users nearby (if the sensor is not in Silent Mode).
Ending an active Emergency
During an active Emergency, caused by the Wet state of the sensor, it will update with data every 5 minutes. Changing the state of the sensor to Dry, by wiping off any remaining liquid between any two metal rods on the top and bottom of the sensor will mark the Emergency as Solved (✔️). This means the Owner is aware of the Emergency and the situation is stable, so no need to worry for the other users nearby.
The Solved Event will be automatically removed from the map after 10 minutes from marking as Solved (it can take maximum 20 minutes).
Ending a stale Emergency
For almost all sensors the emergency status will be updated by the consequent data transfers of the originating sensor.
If the sensor is not sending any update after the initial Emergency trigger, for more than ~6 hours, it will become irelevant and it will be automatically ended and removed from the map.
For the current Water Leakage sensor, it means that sending the update signal every 5 minutes with the Wet status will keep the Emergency active indefinitely, until the Owner of the sensor wipes off all remaining liquid.
Troubleshoot
If you think the device is not sending data properly, you can try the following.
- Perform a re-join procedure, to force the sensor to re-join the LoRaWAN network. To perform it, you need to long press on the Test Button for 5 seconds and release. The blue LED will blink quickly and then will stay lit for a couple of seconds if the Join was successful. Now the device is properly sending data over the LoRaWAN network around.
2. Check your Helium coverage at https://explorer.helium.com or https://mappers.helium.com. If you do not have coverage, you can expand the Helium network by installing a compatible Helium gateway. Check it out at https://heliummart.com.
3. In case you do have Helium coverage, make sure the gateways are online in the Helium Explorer, and try to move the sensor around in a different spot of your location. Better, try to join the sensor and check the signal outdoors. If you can use the sensor outdoors, then it might be your building materials are obstructionist the LoRa signal. Try placing the sensor as close to the outside as possible.
4. Last thing you can do is to re-try all the Quick Setup steps. Just delete the sensor from the Update Sensor screen and re-add it as usual.
Still having issues?
You can use the official Lithium Community Discord channel to ask for help.
You can use the website support form here: https://lithium-app.com/support
You can write us an email with a detailed description of the issue at support@lithium-app.com
The original product information, data sheet and user guide may be found on the MerryIoT website here: https://www.merryiot.com/Product/Detail/4